ELASTOPHENE FLAM 25 PDF

admin

ELASTOPHENE® FLAM 25 AR T3 is a SBS elastomeric bitumen waterproofing membrane with a glass grid / glass fleece reinforcement. The topside is protected . ELASTOPHENE® 25 AR must be applied by torch-on techniques on a weldable underlayer (FLAM) or bonded with bitumen (EAC free of oxidized bitumen) on a. ELASTOPHENE® FLAM is a flexible SBS elastomeric bitumen waterproofing membrane with a non-woven polyester reinforcement. Both sides are.

Author: Yozshuzshura Daikinos
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Photos
Published (Last): 22 September 2018
Pages: 94
PDF File Size: 16.29 Mb
ePub File Size: 16.84 Mb
ISBN: 913-7-74247-960-3
Downloads: 90972
Price: Free* [*Free Regsitration Required]
Uploader: Zuludal

Fitting the 2nd layer in front of the future rain collector. The photos on this page describe the work. La partie bitume fait approximativement 2. The weekend brings heavy rain to test the waterproofing — not a drop gets through to the house. Finition autour de la platine. The rain water collector is positioned through a hole cut in the sidewall reinforcement, and then heated to glue it to the sidewall. Applying the insulation requires careful attention to the weather forecast and the planning of the work.

Welding the outer reinforcement onto the collector. The orientation of the elastophwne layer depends on the way in which the third layer will be applied. As with the 1st layer, the joint of the flat roof and the rising walls that surround the roof are a possible source ellastophene leaks. The Elastophene 25 is rolled out and cut to fit. Heating the outer-reinforcement and the collector. Cliquer sur les elastoohene pour les agrandir. The first layer and the sidewall reinforcement are complete after 4 days.

These are ajusted now but will be fitted later taking into account the future height of the finished surface. Click on photo to enlarge. Since the new waterproofing and the insulation will raise the roof, the rainwater drains must also be raised.

  BOURNS 3296 VARIABLE RESISTOR PDF

elasyophene

Soudage du renfort sur platine et dalle. The rain water collector will pass through this. When reading estimates for waterproofing on flat roofs you may find that the estimate is lightened to reduce the price. Rodolphe Ferracane, e-mail contact AFR-etancheite. The joint of the flat roof and the rising walls that surround the roof are a possible source of leaks.

Removal of remnants of previous waterproofing. The first layer, which provides the waterproofing, is of elastic bitumen, 2. Creative Commons Attribution – Pas de Modification 3.

Pas une goute n’entre dans la maison. The top serface is covered with flakes of stone which protect it against the ultra-violet.

Reinforcement at junction of standups. Because fla are few right angles, there are lots of triangles to be filled in.

Click on the photos to enlarge them. Cinq points de Sopracolle par plaque.

ELASTOPHENE FLAM – Soprema

Click on figure to enlarge. The figure shows the three layers and the sidewall reinforcement for each layer. The time has come to re-do the waterproofing on the terrace roof of my house. If there is a risk of rain, then the Knauf Thane ET glued to the first layer must be entirely enclosed by the second layer, even if this means performing work not needed by the final waterproofing.

Last elastopheene of the weekend’s heavy rain. On my roof, the rolls of the final layer are positioned north-south, so the second layer must be east-west.

  CINEANTROPOMETRIA DEFINICION PDF

ELASTOPHENE® FLAM 25 – Soprema

For example the first layer could be omitted, and the insulation glued directly to the existing surface. Before the insulation is laid, the channels carrying the rain water are reinforced: The work specified by this standard is often referred to as Three layers plus insulation, with heated reinforcement.

Il est bien plus rapide de remplacer les renforts par le flashing: Finishing around rain water collector See 2. Chauffage du sur-renfort et de la platine.

It prevents water vapour reaching the insulation, and serves as a base for the finishing layer. The collector is trimmed before applying the outer reinforcement.

This second layer of bitumen should be placed on the Knauf Thane ET within a few hours to ensure that the Sopracolle glue speads out under elastoophene pressure of the layer of bitumen above.

Cutting nord end of a roll of finishing layer. Creative Commons Attribution – NoDerivs 3.

The two layers should be perpendicular to one another. Bitumous glue is applied to the rising side walls.

ELASTOPHENE® 25

The second bitumous layer is of the same material as the first. Before work begins, the existing concrete surface was cleaned with a high pressure bar hose equipped with a rotating jet. L’isolation Knauf Thane ET. Good waterproofing requires a reinforcing piece between the roof and the wall. The third bitumous layer is a reinforced bitumen with its lower face covered by a film which melts when heated, gluing it to the epastophene layer.

Subscribe US Now